Wood, a natural material with versatile industrial applications, faces limitations such as low dimensional stability and decay resistance. To address these issues, there has been significant progress in wood modification research. Oil heat treatment has emerged as an effective method among environmentally friendly wood treatment options. Studies have indicated that treating wood with hot vegetable oils yields superior properties compared to traditional methods involving gaseous atmospheres, which is attributed to the synergistic effect of oils and heat. This comprehensive review investigates the physical, chemical, and mechanical modifications induced by the oil heat treatment of wood, along with its impact on biological durability against biotic agents. The review synthesizes recent research findings, elucidates underlying mechanisms, and discusses the implications for wood material science and engineering. Full article

This paper proposes a control strategy for grid-following inverter control and grid-forming inverter control developed for a Solar Photovoltaic (PV)–battery-integrated microgrid network. A grid-following (GFL) inverter with real and reactive power control in a solar PV-fed system is developed; it uses a Phase Lock Loop (PLL) to track the phase angle of the voltages at the PCC and adopts a vector control strategy to adjust the active and reactive currents that are injected into the power grid. The drawback of a GFL inverter is that it lacks the capability to operate independently when the utility grid is down due to outages or disturbances. The proposed grid-forming (GFM) inverter control with a virtual synchronous machine provides inertia to the grid, generates a stable grid-like voltage and frequency and enables the integration of the grid. The proposed system incorporates a battery energy storage system (BESS) which has inherent energy storage capability and is independent of geographical areas. The GFM control includes voltage and frequency control, enhanced islanding and black start capability and the maintenance of the stability of the grid-integrated system. The proposed model is validated under varying irradiance conditions, load switching, grid outages and temporary faults with fault ride-through (FRT) capability, and fast frequency response and stability are achieved. The proposed model is validated under varying irradiance conditions, load switching, grid outages and line faults incorporating fault ride-through capability in GFM-based control. The proposed controller was simulated in a 100 MW solar PV system and 60 MW BESS using the MATLAB/Simulink 2023 tool, and the experimental setup was validated in a 1 kW grid-connected system. The percentage improvement of the system frequency and voltage with FRT-capable GFM control is 69.3% and 70%, respectively, and the percentage improvement is only 3% for system frequency and 52% for grid voltage in the case of an FRT-capable GFL controller. The simulation and experimental results prove that GFM-based inverter control achieves fast frequency response, and grid stability is also ensured. Full article

A novel low-NO_x burner was proposed in this study to achieve the stable and clean combustion of low- and medium-calorific-value gas and promote energy sustainability, and the influence of the gas pipe structure on the burner’s characteristics was studied with coke oven gas as a fuel. A 40 kW burner test bench was established to conduct cold-state experiments to investigate the influences of the gas pipe structure on the aerodynamic characteristics of the burner. We performed numerical simulations on both a 40 kW burner and a 14 MW prototype burner to investigate the thermal performance of the burners and their impact on low NO_x emissions. The experimental results showed that increasing the deflection angle of the gas pipe nozzle direction relative to the circumferential tangent direction, the high-velocity zone and the high-concentration zone of the flow field move towards the central axis. Increasing the bending angle of gas pipe nozzle direction relative to the axis direction caused the high-velocity zone and the high-concentration zone to move upstream direction of the jet. The simulation reveals that the NO concentration at the exit cross-section of the combustion chamber of the 14 MW prototype burner is 17.00 mg/m³ (with 3.5% oxygen content). A recommended design structure of the burner was proposed, with a deflection angle of 0°and a bending angle of 0° for the No. 3 gas pipe, and a deflection angle of 15° and a bending angle of 30° for the No. 4 gas pipe. Full article

Electro-optic modulators (EOMs) are pivotal in bridging electrical and optical domains, essential for diverse applications including optical communication, microwave signal processing, sensing, and quantum technologies. However, achieving the trifecta of high-density integration, cost-effectiveness, and superior performance remains challenging within established integrated photonics platforms. Enter thin-film lithium niobate (LN), a recent standout with its inherent electro-optic (EO) efficiency, proven industrial performance, durability, and rapid fabrication advancements. This platform inherits material advantages from traditional bulk LN devices while offering a reduced footprint, wider bandwidths, and lower power requirements. Despite its recent introduction, commercial thin-film LN wafers already rival or surpass established alternatives like silicon and indium phosphide, benefitting from decades of research. In this review, we delve into the foundational principles and technical innovations driving state-of-the-art LN modulator demonstrations, exploring various methodologies, their strengths, and challenges. Furthermore, we outline pathways for further enhancing LN modulators and anticipate exciting prospects for larger-scale LN EO circuits beyond singular components. By elucidating the current landscape and future directions, we highlight the transformative potential of thin-film LN technology in advancing electro-optic modulation and integrated photonics. Full article

Hydraulic infrastructures are susceptible to deformation over time, necessitating reliable monitoring and prediction methods. In this study, we address this challenge by proposing a novel approach based on the combination of Variational Mode Decomposition (VMD), Convolutional Neural Network (CNN), and Long Short-Term Memory (LSTM) methods for Global Navigation Satellite Systems (GNSS) deformation monitoring and prediction modeling. The VMD method is utilized to decompose the complex deformation signals into intrinsic mode functions, which are then fed into a CNN method for feature extraction. The extracted features are input into an LSTM method to capture temporal dependencies and make predictions. The experimental results demonstrate that the proposed VMD-CNN-LSTM method exhibits an improvement by about 75%. This research contributes to the advancement of deformation monitoring technologies in water conservancy engineering, offering a promising solution for proactive maintenance and risk mitigation strategies. Full article

Addressing the challenges posed by the complexity of the structure and the multitude of sensor types installed in space application fluid loop systems, this paper proposes a fault diagnosis method based on an improved D-S evidence theory. The method first employs the Gaussian affiliation function to convert the information acquired by sensors into BPA functions. Subsequently, it utilizes a pignistic probability transformation to convert the multiple subset focal elements into single subset focal elements. Finally, it comprehensively evaluates the credibility and uncertainty factors between evidences, introducing Bray–Curtis dissimilarity and belief entropy to achieve the fusion of conflicting evidence. The proposed method is initially validated on the classic Iris dataset, demonstrating its reliability. Furthermore, when applied to fault diagnosis in space application fluid circuit loop pumps, the results indicate that the method can effectively fuse multiple sensors and accurately identify faults. Full article

Narrowband afterglow materials display interesting functions in high-quality anti-counterfeiting and multiplexed bioimaging. However, there is still a limited exploration of these afterglow materials, especially for those with a full width at half maxima (FWHM) around 30 nm. Here, we report the fabrication of narrowband organic/inorganic hybrid afterglow materials via energy transfer technology. Coronene (Cor) with a long phosphorescence feature and broad phosphorescence band is selected as the donor for energy transfer, and inorganic quantum dots (QDs) of CdSe/ZnS with a narrowband emission are used as acceptors. Upon doping into the organic matrix, the resultant three-component materials exhibit a narrowband afterglow with an afterglow lifetime of approximately 3.4 s and an FWHM of 31 nm. The afterglow wavelength of the afterglow materials can be controlled by the QDs. This work based on organic/inorganic hybrids provides a facile approach for developing multicolor and narrowband afterglow materials, as well as opens a new way for expanding the features of organic afterglow for multifunctional applications. It is expected to rely on narrowband afterglow emitters to solve the “spectrum congestion” problem of high-density information storage in optical anti-counterfeiting and information encryption. Full article

This qualitative study explores the utilization of social media among Pakistani pilgrims during spiritual journeys and investigates its impact on their pilgrimage experiences. Thirty Pakistani pilgrims who had embarked on spiritual journeys to various religious sites were interviewed using semi-structured interviews. Thematic analysis was employed to analyze the interview transcripts, revealing five main stages of social media usage: pre-trip preparation, real-time updates and guidance, community building and support, sharing experiences and insights, and post-trip reflection and engagement. At each stage, social media played diverse roles, including providing information and support, fostering connections with fellow pilgrims, sharing personal experiences, and facilitating spiritual dialogue. This explorative study underscores the significance of social media in enhancing the pilgrimage experience for Pakistani pilgrims, serving as a valuable tool for information dissemination, community building, spiritual support, and personal reflection throughout the pilgrimage journey. The findings contribute to a deeper understanding of how social media shapes pilgrims’ experiences and fosters their spiritual growth, emphasizing the need for further research to explore the nuanced dynamics of social media usage in the context of pilgrimage. Overall, this study sheds light on the unique role of social media in the spiritual journeys of Pakistani pilgrims and highlights its implications for pilgrimage practices and the broader discourse on religious tourism. Full article

The proposed Mars missions will expose astronauts to long durations of social isolation (SI) and space radiation (SR). These stressors have been shown to alter the brain’s macrostructure and microenvironment, including the blood–brain barrier (BBB). Breakdown of the BBB is linked to impaired executive functions and physical deficits, including sensorimotor and neurocognitive impairments. However, the precise mechanisms mediating these effects remain unknown. Additionally, the synergistic effects of combined exposure to SI and SR on the structural integrity of the BBB and brain remain unknown. We assessed the BBB integrity and morphology in the brains of male rats exposed to ground-based analogs of SI and SR. The rats exposed to SR had enlarged lateral ventricles and increased BBB damage associated with a loss of astrocytes and an increased number of leaky vessels. Many deficits observed in SR-treated animals were attenuated by dual exposure to SI (DFS). SI alone did not show BBB damage but did show differences in astrocyte morphology compared to the Controls. Thus, determining how single and combined inflight stressors modulate CNS structural integrity is crucial to fully understand the multiple pathways that could impact astronaut performance and health, including the alterations to the CNS structures and cell viability observed in this study. Full article

Developing microwave absorbers with superior low-frequency electromagnetic wave absorption properties is one of the foremost important factors driving the boom in 5G technology development. In this study, via a simple hydrothermal and pyrolysis strategy, randomly interleaved CoNiO₂ nanosheets and uniformly ultrafine CoNi nanocrystals are anchored onto both sides of a single-layered MXene. The absorption mechanism demonstrated that the hierarchical heterostructure prevents the aggregation of MXene nanoflakes and magnetic crystallites. In addition, the introduction of the double-magnetic phase of CoNiO₂/CoNi arrays can not only enhance the magnetic loss capacity but also generate larger void spaces and abundant heterogeneous interfaces, collectively promoting impedance-matching and furthering microwave attenuation capabilities at a low frequency. Hence, the reflection loss of the optimal absorber (M–MCNO) is −45.33 dB at 3.24 GHz, which corresponds to a matching thickness of 5.0 mm. Moreover, its EAB can entirely cover the S-band and C-band by tailoring the matching thickness from 2 to 7 mm. Satellite radar cross-section (RCS) simulations demonstrated that the M–MCNO can reduce the RCS value to below −10 dB m² over a multi-angle range. Thus, the proposed hybrid absorber is of great significance for the development of magnetized MXene composites with superior low-frequency microwave absorption properties. Full article

Trioza erytreae (Del Guercio, 1918) (Hemiptera: Triozidae) is a citrus pest which produces gall symptoms on leaves and transmits bacteria associated with the citrus disease Huanglongbing, ‘Candidatus Liberibacter’ spp. In the present work, the biology and behaviour of T. erytreae were studied in different rootstock–cultivar combinations. Six rootstocks were used, Flying dragon (FD), ‘Cleopatra’ mandarin (CL), Carrizo citrange (CC), Forner-Alcaide no.5 (FA5), Forner-Alcaide no.517 (FA517) and Citrus macrophylla (CM), and six scion cultivars: ‘Star Ruby’, ‘Clemenules’, ‘Navelina’, ‘Valencia Late’, ‘Fino 49’ and ‘Ortanique’. Survival and oviposition were evaluated in a no-choice trial, and preference in a choice trial, all of them under greenhouse conditions. Trioza erytreae did not show a clear settle preference for any citrus combination. However, it was able to lay more eggs in ‘Fino 49’ grafted on CC than on FD. In terms of survival, ‘Ortanique’ grafted onto FA5 was more suitable than when grafted onto FA517, and in the case of ‘Valencia Late’, when it was grafted onto CM rather than CC. Our results showed that T. erytreae behave differently depending on the citrus combination. Full article

Non-specific low back pain (NSLBP) in children and adolescents has increased in recent years, and the evidence of the physiotherapy interventions in back care needs to be updated. Our main goal was to quantify the effects of preventive physiotherapy interventions on improving behavior and knowledge related to back care and prevention of NSLBP in children and adolescents. Based on two previous meta-analyses, Cochrane Library, MEDLINE, PEDro, Web of Science, LILACS, IBECS, PsycINFO, and IME databases and several journals were searched. Two researchers independently extracted data and assessed the risk of bias in the studies using the RoB2 tool. Data were described according to PRISMA guidelines. A total of 24 studies (28 reports) were included. In the posttest, the behavior variable obtained an overall effect size of d₊ = 1.48 (95%CI: 0.40 to 2.56), and the knowledge variable obtained an effect size of d₊ = 1.41 (95%CI: 1.05 to 1.76). Physiotherapy has demonstrated beneficial impacts on behavior and knowledge concerning back care and to prevent NSLBP in children and adolescents. Interventions focusing on postural hygiene and exercise should be preferred, especially those that are shorter in number of weeks, more intense, and incorporate as many intervention hours as possible. Full article

Background: Studies suggest that chronic psychological stress can lead to oral health deterioration, alter the immune response, and possibly contribute to increased inflammation, which can impact the physiological healing of periodontal tissues. This cross-sectional study seeks to assess and improve clinical understanding regarding the relationship between perceived stress, mindfulness, and periodontal health. Methods: A total of 203 people were analyzed from December 2022 to June 2023. The Periodontal Screening and Recording (PSR) score and Gingival Bleeding Index (GBI), and Plaque Control Record (PCR) of every patient were registered. Subsequently, participants completed the Sheldon Cohen Perceived Stress Scale (PSS) and the Mindfulness Awareness Attention Scale (MAAS) questionnaires. The collected data underwent statistical analysis, encompassing the evaluation of correlations and dependencies. Applying Welch’s t-test to assess the relationship between MAAS and the variable indicating the presence or absence of periodontitis, a noteworthy p-value of 0.004265 was obtained. Results: This underscores a significant distinction in MAAS scores between patients affected by periodontitis and those unaffected by the condition. Additionally, Pearson correlations were computed for GBI and perceived stress, PCR and perceived stress, PCR and MAAS. The resulting p-values of 2.2–16, 3.925–8, and 2.468–8, respectively, indicate a statistically significant correlation in each instance. Conclusions: These findings contribute valuable insights into the interconnectedness of these variables, emphasizing the significance of their associations in the study context. Despite the limitations, the findings of this study suggest a significant relationship between psychological stress, mindfulness, and periodontal tissue health. Clinical trials are necessary to incorporate the assessment of a patient’s psychological status as a new valuable tool in the management of periodontal health. Full article

Water used for water supply undergoes numerous changes that affect its composition prior to entering the water supply system (WSS). Once it enters the WSS, it is subject to numerous influences altering its physical and chemical composition, redox potential, and microbial quality. Observations of water quality parameters at different locations within the WSS indicate that it is justified to assume that these processes take place from the source to the end user. In this study, we used the results of routine everyday analyses (EC, T, pH, ORP, chloride, nitrate, nitrite, ammonium, and bacteria) supplemented by experimental data from a one-year sampling campaign assessing the main cations and anions and stable isotopes δ²H and δ¹⁸O. Through these data, the statistical significance of the differences between the concentrations of the basic water quality parameters among different WSS locations was determined, together with the water retention time in the system. The results indicate minor changes in water chemical composition within the observed WSS, remaining below the prescribed Maximum Contaminant Level (MCL) for human consumption. However, factors such as water retention time, CaCO₃ deposition, pH fluctuations, and bacterial growth may influence its suitability, which necessitates further investigation into potential risks affecting water quality. Full article

Electric vehicle (EV) charging facilities are essential to their development and deployment. These days, autonomous microgrids that use renewable energy resources to energize charging stations for electric vehicles alleviate pressure on the public electricity grid. Nevertheless, controlling and managing such charging stations’ energy is difficult due to the nonlinearity and irregular character of renewable energy sources. The current research recommends using a Brain Emotional Learning Intelligent Control (BELBIC) controller to enhance an autonomous EV charging station’s performance and power management. The charging station uses a battery to store energy and is primarily powered by photovoltaic (PV) solar energy. The principles of BELBIC are dependent on emotional cues and sensory inputs, and they are based on an emotion processing system in the brain. Noise and parameter variations do not affect this kind of controller. In this study, the performance of a conventional proportional–integral (PI) controller and the suggested BELBIC controller is evaluated for variations in solar insolation. The various parts of an EV charging station are simulated and modelled by the MATLAB/Simulink framework. The findings show that, in comparison to the conventional PI controller, the suggested BELBIC controller greatly enhances the transient responsiveness of the EV charging station’s performance. The EV keeps charging while the storage battery perfectly saves and keeps steady variations in PV power, even in the face of any PV insolation disturbances. The suggested system’s simulation results are provided and scrutinized to confirm the concept’s suitability. The findings validate the robustness of the suggested BELBIC control versus parameter variations. Full article

Particle image velocimetry (PIV) measurements were performed inside a low-pressure turbine cascade operating at engine-relevant high-speed and low-Re conditions to investigate the near-endwall flow. Of particular research interest was the dominant periodic disturbance of the flow field by incoming wakes, which were generated by moving cylindrical bars at a frequency of 500 Hz. Two PIV setups were utilized to resolve both (1) a large blade-to-blade plane close to the endwall as well as midspan and (2) the wake effects in an axial flow field downstream of the blade passage. The measurements were performed using a phase-locked approach in order to align and compare the results with comprehensive CFD data that are also available for this test case. The experimental results not only support a better understanding and even a quantification of the wake-induced over/under-turning inside and downstream of the passage, they also enable the tracing of the `negative-jet-effect’, which is widely known in the CFD branch of the turbomachinery community but is seldom visualized in experiments. The results also reveal that the bar wake periodically widens the blade wake by up to 165%, while the secondary flow is less affected and exhibits a phase lag with respect to the 2D-flow effects. The results presented here are an essential basis for the subsequent investigation of the near-endwall blade suction surface effects using unsteady pressure-sensitive paint in the second part of this two-part publication. Full article

Analytical modelling is an effective approach to obtaining a gear dynamic response or vibration pattern for health monitoring and useful life prediction. Many researchers have modelled this response with various fault conditions commonly observed in gears. The outcome of such models provides a good idea about the changes in the dynamic response available between different gear health states. Hence, a catalogue of the responses is currently available, which ought to aid predictions of the health of actual gears by their vibration patterns. However, these analytical models are limited in providing solutions to useful life prediction. This may be because a majority of these models used single fault conditions for modelling and are not valid to predict the remaining life of gears undergoing more than one fault condition. Existing reviews related to gear faults and dynamic modelling can provide an overview of fault modes, methods for modelling and health prediction. However, these reviews are unable to provide the critical similarities and differences in the single-fault dynamic models to ascertain the possibility of developing models under combined fault modes. In this paper, existing analytical models of spur gears are reviewed with their associated challenges to predict the gear health state. Recommendations for establishing more realistic models are made especially in the context of modelling combined faults and their possible impact on gear dynamic response and health prediction. Full article

Glass waste products represent a significant environmental concern, with an estimated 1.4 billion tons being landfilled globally and 200 million tons annually. This results in a significant use of land resources. Therefore, it would be highly advantageous to develop a new method for disposing of waste glass. Waste glass can be recycled and ground into waste glass powder (WGP) for use in solidified soil applications as a sustainable resource. This study is based on solidified soil research, wherein NaOH, Ca(OH)₂, and Na₂SO₄ were incorporated as activators to enhance the reactivity of WGP. The optimal solidified soil group was determined based on unconfined compressive strength tests, which involved varying the activator concentrations and WGP content in combination with cement. X-ray diffraction (XRD) was used to study the composition of solidified soil samples. Microscopic pore characteristics were investigated using scanning electron microscopy (SEM), and the Image J software was employed to quantify the number and size of pores. Fourier-transform infrared spectroscopy (FTIR) was employed to examine the activation effect of waste glass powder. This study investigated the solidification mechanism and porosity changes. The results demonstrate that the addition of activated WGP to solidified soil enhances its strength, with a notable 12% increase in strength achieved using a 6% Ca(OH)₂ solution. The use of 2% concentration of Na₂SO₄ and NaOH also shows an increase in strength of 7.6% and 8.6%, respectively, compared to the sample without WGP. The XRD and SEM analyses indicate that activated WGP enhances the content of hydrates, reduces porosity, and fosters the formation of a more densely packed solidified soil structure. Full article

As an innovative form in the digital age, VR art exhibitions have attracted increasing attention. This study aims to explore the key factors that influence visitors’ continuance intention to VR art exhibitions using the expectation confirmation model and experience economy theory and to explore ways to enhance visitor immersion in virtual environments. We conducted a quantitative study of 235 art professionals and enthusiasts, conducted using the partial least squares structural equation modeling (PLS-SEM), to examine the complex relationship between confirmation (CON), Perceived Usefulness (PU), Aesthetic Experiences (AE), Escapist Experiences (EE), Satisfaction (SAT), and Continuance Intention (CI). The results show that confirmation plays a key role in shaping PU, AE, and EE, which in turn positively affect visitors’ SAT. Among these factors, AE positively impacts PU, but EE have no impact. A comprehensive theoretical model was then constructed based on the findings. This research provides empirical support for designing and improving VR art exhibitions. It also sheds light on the application of expectation confirmation theory and experience economy theory in the art field to improve user experience and provides theoretical guidance for the sustainable development of virtual digital art environment. Full article

According to the current guidelines, additional surgery is performed for endoscopically resected specimens of early colorectal cancer (CRC) with a high risk of lymph node metastasis (LNM). However, the rate of LNM is 2.1–25.0% in cases treated endoscopically followed by surgery, indicating a high rate of unnecessary surgeries. Therefore, this study aimed to develop an artificial intelligence (AI) model using H&E-stained whole slide images (WSIs) without handcrafted features employing surgically and endoscopically resected specimens to predict LNM in T1 CRC. To validate with an independent cohort, we developed a model with four versions comprising various combinations of training and test sets using H&E-stained WSIs from endoscopically (400 patients) and surgically resected specimens (881 patients): Version 1, Train and Test: surgical specimens; Version 2, Train and Test: endoscopic and surgically resected specimens; Version 3, Train: endoscopic and surgical specimens and Test: surgical specimens; Version 4, Train: endoscopic and surgical specimens and Test: endoscopic specimens. The area under the curve (AUC) of the receiver operating characteristic curve was used to determine the accuracy of the AI model for predicting LNM with a 5-fold cross-validation in the training set. Our AI model with H&E-stained WSIs and without annotations showed good performance power with the validation of an independent cohort in a single center. The AUC of our model was 0.758–0.830 in the training set and 0.781–0.824 in the test set, higher than that of previous AI studies with only WSI. Moreover, the AI model with Version 4, which showed the highest sensitivity (92.9%), reduced unnecessary additional surgery by 14.2% more than using the current guidelines (68.3% vs. 82.5%). This revealed the feasibility of using an AI model with only H&E-stained WSIs to predict LNM in T1 CRC. Full article

Gastric perforation refers to the complete rupture of the gastric wall, leading to the extravasation of gastric contents into the thoracic cavity or peritoneum. Without timely intervention, the expulsion of gastric contents may culminate in profound discomfort, exacerbating the inflammatory process and potentially triggering perilous sepsis. In clinical practice, surgical suturing or endoscopic closure procedures are commonly employed. Magnetic-driven microswarms have also been employed for sealing gastrointestinal perforation. However, surgical intervention entails significant risk of bleeding, while endoscopic closure poses risks of inadequate closure and the need for subsequent removal of closure clips. Moreover, the efficacy of microswarms is limited as they merely adhere to the perforated area, and their sealing effect diminishes upon removal of the magnetic field. Herein, we present a Fe&Mg@Lard-Paraffin micromotor (LPM) constructed from a mixture of lard and paraffin coated with magnesium (Mg) microspheres and iron (Fe) nanospheres for sutureless sealing gastric perforations. Under the control of a rotating magnetic field, this micromotor demonstrates precise control over its movement on gastric mucosal folds and accurately targets the gastric perforation area. The phase transition induced by the high-frequency magnetothermal effect causes the micromotor composed of a mixed oil phase of lard and paraffin to change from a solid to a liquid phase. The coated Mg microspheres are subsequently exposed to the acidic gastric acid environment to produce a magnesium protonation reaction, which in turn generates hydrogen (H₂) bubble recoil. Through a Mg-based micropower traction, part of the oil phase could be pushed into the gastric perforation, and it would then solidify to seal the gastric perforation area. Experimental results show that this can achieve long-term (>2 h) gastric perforation sealing. This innovative approach holds potential for improving outcomes in gastric perforation management. Full article

Given the widespread use of esters and polyesters in products like cosmetics, fishing nets, lubricants and adhesives, whose specific application(s) may cause their dispersion in open environments, there is a critical need for stringent eco-design criteria based on biodegradability and ecotoxicity evidence. Our approach integrates experimental and computational methods based on short oligomers, offering a screening tool for the rapid identification of sustainable monomers and oligomers, with a special focus on bio-based alternates. We provide insights into the relationships between the chemical structure and properties of bio-based oligomers in terms of biodegradability in marine environments and toxicity in benchmark organisms. The experimental results reveal that the considered aromatic monomers (terephthalic acid and 2,5-furandicarboxylic acid) accumulate under the tested conditions (OECD 306), although some slight biodegradation is observable when the inoculum derives from sites affected by industrial and urban pollution, which suggests that ecosystems adapt to non-natural chemical pollutants. While clean seas are more susceptible to toxic chemical buildup, biotic catalytic activities offer promise for plastic pollution mitigation. Without prejudice to the fact that biodegradability inherently signifies a desirable trait in plastic products, nor that it automatically grants them a sustainable “license”, this study is intended to facilitate the rational design of new polymers and materials on the basis of specific uses and applications. Full article