Bearings are crucial components of machinery and equipment, and it is essential to inspect them thoroughly to ensure a high pass rate. Currently, bearing scratch detection is primarily carried out manually, which cannot meet industrial demands. This study presents research on the detection of bearing surface scratches. An improved YOLOV5 network, named YOLOV5-CDG, is proposed for detecting bearing surface defects using scratch images as targets. The YOLOV5-CDG model is based on the YOLOV5 network model with the addition of a Coordinate Attention (CA) mechanism module, fusion of Deformable Convolutional Networks (DCNs), and a combination with the GhostNet lightweight network. To achieve bearing surface scratch detection, a machine vision-based bearing surface scratch sensor system is established, and a self-made bearing surface scratch dataset is produced as the basis. The scratch detection final Average Precision (AP) value is 97%, which is 3.4% higher than that of YOLOV5. Additionally, the model has an accuracy of 99.46% for detecting defective and qualified products. The average detection time per image is 263.4 ms on the CPU device and 12.2 ms on the GPU device, demonstrating excellent performance in terms of both speed and accuracy. Furthermore, this study analyzes and compares the detection results of various models, demonstrating that the proposed method satisfies the requirements for detecting scratches on bearing surfaces in industrial settings. Full article

This paper addresses the optimal sizing of Hybrid Renewable Energy Systems (HRESs), encompassing wind, solar, and battery systems, with the aim of delivering reliable performance at a reasonable cost. The focus is on mitigating unscheduled outages on the national grid in Iraq. The proposed On–off-grid HRES method is implemented using MATLAB and relies on an iterative technique to achieve multi-objectives, balancing reliability and economic constraints. The optimal HRES configuration is determined by evaluating various scenarios related to energy flow management, electricity prices, and land cover effects. Consumer requirements regarding cost and reliability are factored into a 2D optimization process. A battery model is developed to capture the dynamic exchange of energy among different renewable sources, battery storage, and energy demands. A detailed case study across fifteen locations in Iraq, including water, desert, and urban areas, revealed that local wind speed significantly affects the feasibility and efficiency of the HRES. Locations with higher wind speeds, such as the Haditha lake region (payback period: 7.8 years), benefit more than urban areas (Haditha city: payback period: 12.4 years). This study also found that not utilizing the battery, particularly during periods of high electricity prices (e.g., 2015), significantly impacts the HRES performance. In the Haditha water area, for instance, this technique reduced the payback period from 20.1 to 7.8 years by reducing the frequency of charging and discharging cycles and subsequently mitigating the need for battery replacement. Full article

Osteoporosis is the most common metabolic bone disorder and is characterized by decreased bone density, which has a relationship with the quality of life among the aging population. Previous research has found that activation of the dopamine D1 receptor can improve bone mass formation. SKF38393 is an agonist of dopamine D1 receptors. However, as a small-molecule drug, SKF38393 is unstable and releases quickly. The aim of this study was to prototype polylactic-co-glycolic acid (PLGA)/SKF38393 microspheres and assess their potential osteogenic effects compared to those under the free administration of SKF38393. The cytocompatibility of PLGA/SKF38393 was determined via CCK-8 and live/dead cell staining; the osteogenic effects in vitro were determined with ALP and alizarin red staining, qRT-PCR, and Western blotting; and the in vivo effects were assessed using 25 Balb/c mice. We also used a PCR array to explore the possible signaling pathway changes after employing PLGA/SKF38393. Our experiments demonstrated that the osteogenic effect of D1Rs activated by the PLGA/SKF38393 microsphere was better than that under free administration, both in vitro and in vivo. According to the PCR array, this result might be associated with six signaling pathways (graphical abstract). Ultimately, in this study, we prototyped PLGA/SKF38393, demonstrated its effectiveness, and preliminarily analyzed its mechanism of action. Full article

To establish a responsible business environment, it is important to analyze the way corporate social responsibility (CSR) is implemented within the business world. In this respect, managers play a crucial role in designing and applying the CSR concept and practices. Therefore, this paper aims to identify and analyze the perceptions and attitudes of medium-sized enterprises (SMEs) and multinational companies (MNCs) managers in the Romanian retail sector related to CSR implementation. A documentary research approach and a qualitative research methodology through the use of four focus groups were utilized to fulfill the above-mentioned purpose. Additionally, the authors employed content analysis and Nvivo 14 software to process the collected data. The findings indicate that the size of firms represents a key element of managers’ perceptions and attitudes regarding CSR. Particularly, SME managers have a lower level of familiarity with the concept and the potential advantages for business compared to MNC managers. Furthermore, when it comes to CSR practices, MNCs use a comprehensive approach to meeting the demands of their stakeholders, whereas SMEs prioritize the requirements of their employees. One major obstacle in implementing the CSR concept continues to be the high expenses involved in the businesses. Full article

Cyanobacterial blooms represent a common environmental issue in aquatic systems, and these blooms bring forth numerous hazards, with the generation of volatile organic compounds (VOCs) being one of them. Global climate change has led to alterations in various climatic factors affecting algal growth, indirectly impacting the quantity of VOCs released by algae. With advancements in remote sensing technology, exploration of the spatiotemporal distributions of algae in large water bodies has become feasible. This study focuses on Taihu Lake, characterized by frequent occurrences of cyanobacterial blooms. Utilizing MODIS satellite imagery from 2001 to 2020, we analyzed the spatiotemporal characteristics of cyanobacterial blooms in Taihu Lake and its subregions. Employing the LightGBM machine learning model and the (SHapley Additive exPlanations) SHAP values, we quantitatively analyzed the major meteorological drivers influencing cyanobacterial blooms in each region. VOC-related source spectra and emission intensities from cyanobacteria in Taihu Lake are collected based on the literature review and are used to compile the first inventory of VOC emissions from blue-green algae blooms in Taihu Lake. The results indicate that since the 21st century, the situation of cyanobacterial blooms in Taihu Lake has continued to deteriorate with increasing variability. The relative impact of meteorological factors varies across different regions, but temperature consistently shows the highest sensitivity in all areas. The VOCs released from the algal blooms increase with the proliferation of the blooms, posing a continuous threat to the atmospheric environment of the surrounding cities. This study aims to provide a scientific basis for further improvement of air quality in urban areas adjacent to large lakes. Full article

Acerola (Malpighia emarginata DC.) is a sub-tropical and tropical fruit renowned for its high levels of vitamin C and phenolic compounds, which offer health benefits. This study aimed to optimize the spray drying process by determining the inlet and outlet temperatures using response surface methodology (RSM) with the central composite design. Additionally, it aimed to evaluate the release kinetics in the hydrophilic food simulation environment and the stability of the resulting powder under various storage temperatures. The RSM method determined the optimal inlet and outlet temperatures as 157 °C and 91 °C, respectively. High-accuracy prediction equations (R² ≥ 0.88) were developed for moisture content (3.02%), process yield (91.15%), and the encapsulation yield of total polyphenol content (61.44%), total flavonoid content (37.42%), and vitamin C (27.19%), with a predicted monolayer moisture content below 4.01%, according to the BET equation. The powder exhibited good dissolution characteristics in the acidic hydrophilic food simulation environment and showed greater stability when stored at 10 °C for 30 days, compared to storage at 35 °C and 45 °C. Full article

The rapid spread of Internet of Things technologies has enabled a continuous monitoring of indoor environmental quality in office environments by integrating monitoring devices equipped with low-cost sensors and cloud platforms for data storage and visualization. Critical aspects in the development of such monitoring systems are effective data acquisition, processing, and visualization strategies, which significantly influence the performance of the system both at monitoring device and at cloud platform level. This paper proposes novel strategies to address the challenges in the design of a complete monitoring system for indoor environmental quality. By adopting the proposed solution, one can reduce the data rate transfer between the monitoring devices and the server without loss of information, as well as achieve efficient data storage and aggregation on the server side to minimize retrieval times. Finally, enhanced flexibility in the dashboard for data visualization is obtained, thus enabling graph modifications without extensive coding efforts. The functionality of the developed system was assessed, with the collected data in good agreement with those from other instruments used as references. Full article

Cow dung is a kind of high quality and renewable biological resource. Biochar made from cow dung can be used as a soil amendment to improve soil nutrient status. The relationship between soil water and phosphorus is very close, and the water status determines the form, content, and availability of phosphorus. In order to investigate the effects of biochar on soil inorganic phosphorus components, available phosphorus, enzyme activities related to the phosphorus cycle, microbial functional genes, and seedling growth under different soil water conditions were investigated. Field experiments were carried out by setting different water conditions (30%, 60%, and 100%) and biochar addition (0 t hm⁻², 2.63 t hm⁻², 5.26 t hm⁻², and 7.89 t hm⁻²). The results showed that applying biochar significantly increased the soil’s accessible phosphorus content and the phosphorus content in both the aboveground and subsurface parts of P. euphratica seedlings. This is mainly attributable to biochar’s direct and indirect effects on soil properties. Because biochar is naturally alkaline, it raises soil pH and reduces acid phosphatase activity in the soil around P. euphratica seedlings in the rhizosphere. Perhaps the alkaline phosphatase level first showed an upward trend due to the combined impacts of water and biochar, and then it started to decline when the biochar addition was increased. Soil phosphorus functional genes phoC, phoD, gcd, and pqqc had an increase in copy number with biochar addition but not without treatment. Indirectly, the biochar treatment increased the soil’s phosphorus availability by increasing the population of the phosphate-solubilizing bacteria Fusarium and Sphingomonas. Soil phosphorus availability is positively affected by biochar under various water conditions. This impact is due to chemical and microbiological mechanisms. Full article

Humanity’s strive to understand why and how life appeared on planet Earth dates back to prehistoric times. At the beginning of the 19th century, empirical biology started to tackle this question yielding both Charles Darwin’s Theory of Evolution and the paradigm that the crucial trigger putting life on its tracks was the appearance of organic molecules. In parallel to these developments in the biological sciences, physics and physical chemistry saw the fundamental laws of thermodynamics being unraveled. Towards the end of the 19th century and during the first half of the 20th century, the tensions between thermodynamics and the “organic-molecules-paradigm” became increasingly difficult to ignore, culminating in Erwin Schrödinger’s 1944 formulation of a thermodynamics-compliant vision of life and, consequently, the prerequisites for its appearance. We will first review the major milestones over the last 200 years in the biological and the physical sciences, relevant to making sense of life and its origins and then discuss the more recent reappraisal of the relative importance of metal ions vs. organic molecules in performing the essential processes of a living cell. Based on this reassessment and the modern understanding of biological free energy conversion (aka bioenergetics), we consider that scenarios wherein life emerges from an abiotic chemiosmotic process are both thermodynamics-compliant and the most parsimonious proposed so far. Full article

Background: Percutaneous dilatational tracheostomy (PDT) is the most commonly performed minimally invasive intensive care unit procedure worldwide. Methods: This study evaluated the percentage of consistency between the entry site observed with fiberoptic bronchoscopy (FOB) and the prediction for the PDT level based on pre-procedural ultrasonography (USG) in PDT procedures performed using the forceps dilatation method. The effect of morphological features on intervention sites was also investigated. Complications that occurred during and after the procedure, as well as the duration, site, and quantity of the procedures, were recorded. Results: Data obtained from a total of 91 patients were analyzed. In 57 patients (62.6%), the USG-estimated tracheal puncture level was consistent with the intercartilaginous space observed by FOB, while in 34 patients (37.4%), there was a discrepancy between these two methods. According to Bland Altman, the agreement between the tracheal spaces determined by USG and FOB was close. Regression formulas for PDT procedures defining the intercartilaginous puncture level based on morphologic measurements of the patients were created. The most common complication related to PDT was cartilage fracture (17.6%), which was proven to be predicted with maximum relevance by punctured tracheal level, neck extension limitation, and procedure duration. Conclusions: In PDT procedures using the forceps dilatation method, the prediction of the PDT intervention level based on pre-procedural USG was considerably in accordance with the entry site observed by FOB. The intercartilaginous puncture level could be estimated based on morphological measurements. Full article

In this paper, computational fluid dynamics (CFD) numerical simulation is employed to analyze and discuss the effect of obstacle gradient on the flame propagation characteristics of premixed hydrogen/air in a closed chamber. With a constant overall volume of obstacles, the obstacle blocking rate gradient is set at +0.125, 0, and −0.125, respectively. The study focuses on the evolution of the flame structure, propagation speed, the dynamic process of overpressure, and the coupled flame–flow field. The results demonstrate that the flame front consistently maintains a jet flame as the obstacle gradient increases, with the wrinkles on the flame front becoming increasingly pronounced. When the blocking rate gradients are +0.125, 0, and −0.125, the corresponding maximum flame propagation speeds are measured at 412 m/s, 344 m/s, and 372 m/s, respectively, indicating that the obstacle gradient indeed increases the flame propagation speed. Moreover, the distribution of pressure is closely related to changes in the flame structure, with the overpressure decreasing in the obstacle channel as the obstacle gradient increases. Furthermore, the velocity vector and vortex distribution in the flow field are revealed and compared. It is found that the obstacle tail vortex is the main factor inducing flame evolution and flow field changes in a closed chamber. The effect of the blocking rate gradient on flow velocity is also quantified, with instances of deceleration occurring when the blocking rate gradient is −0.125. Full article

Background and Objectives: Stem cell-based regeneration strategies have shown therapeutic efficacy in various fields of regenerative medicine. These include bone healing after bone augmentation, often complicated by pain, which is managed by using nonsteroidal anti-inflammatory drugs (NSAIDs). However, information is limited about how NSAIDs affect the therapeutic potential of stem cells. Materials and Methods: We investigated the effects of ibuprofen and diclofenac on the characteristics, morphology, and immunophenotype of human mesenchymal stromal cells isolated from the dental pulp (DPSCs) and cultured in vitro, as well as their effects on the expression of angiogenic growth factors (VEGFA and HGF) and selected genes in apoptosis signalling pathways (BAX, BAK, CASP3, CASP9, and BCL2). Results: Ibuprofen and diclofenac significantly reduced the viability of DPSCs, while the expression of mesenchymal stem cell surface markers was unaffected. Both ibuprofen and diclofenac treatment significantly upregulated the expression of HGF, while the expression of VEGFA remained unchanged. Ibuprofen significantly altered the expression of several apoptosis-related genes, including the upregulation of CASP9 and BCL2, with decreased CASP3 expression. BAK, CASP3, CASP9, and BCL2 expressions were significantly increased in the diclofenac-treated DPSCs, while no difference was demonstrated in BAX expression. Conclusions: Our results suggest that concomitant use of the NSAIDs ibuprofen or diclofenac with stem cell therapy may negatively impact cell viability and alter the expression of apoptosis-related genes, affecting the efficacy of stem cell therapy. Full article

A top-down design methodology and implementation of a time domain sensor is presented in this paper. The acceleration resolution of the time domain sensor is equal to the time-measurement accuracy divided by the sensor sensitivity. Combined with the sensitivity formula, the acceleration resolution is proportional to the vibration amplitude, the time-measurement accuracy, and the third power of the resonant frequency. According to the available time-measurement accuracy and the desired acceleration resolution, the parameters including the vibration amplitude and the resonant frequency were theoretically calculated. The geometrical configuration of the time domain sensor device was designed based on the calculated parameters. Then, the designed device was fabricated based on a standard silicon-on-insulator process and a matched interface circuit was developed for the fabricated device. Experimental results demonstrated that the design methodology is effective and feasible. Moreover, the implemented sensor works well. In addition, the acceleration resolution can be tuned by adjusting the time-measurement accuracy and the vibration amplitude. All the reported results of this work can be expanded to other time domain inertial sensors, e.g., a gyroscope or tilt sensor. Full article

Leaf senescence is the last stage of leaf development, and it is accompanied by a leaf color change. In some species, anthocyanins are accumulated during leaf senescence, which are vital indicators for both ornamental and commercial value. Therefore, it is essential to understand the molecular mechanism of anthocyanin accumulation during leaf senescence, which would provide new insight into autumn coloration and molecular breeding for more colorful plants. Anthocyanin accumulation is a surprisingly complex process, and significant advances have been made in the past decades. In this review, we focused on leaf coloration during senescence. We emphatically discussed several networks linked to genetic, hormonal, environmental, and nutritional factors in regulating anthocyanin accumulation during leaf senescence. This paper aims to provide a regulatory model for leaf coloration and to put forward some prospects for future development. Full article

During the COVID-19 pandemic, while some countries succeeded in reducing their rate of death after SARS-CoV-2 infection via vaccination by the end of 2021, some of them also faced hospital capacity strain, leading to social anxiety about delays in the diagnosis and treatment of patients with other diseases. This essay presents an allegory to explain the situation during the COVID-19 pandemic. Through an allegory and Le Morte d’Arthur (Arthur’s Death), this essay indicates that “the scabbard of Excalibur” that we are looking for is an efficient and effective healthcare system that can diagnose patients who might become severely ill due to COVID-19 and to treat them without hospital capacity strain. In Le Morte d’Arthur, the scabbard of Excalibur was lost, and we have not been able to find any alternatives to end the COVID-19 pandemic. We can choose a future in which “the scabbard of Excalibur” exists, providing a different ending for the next pandemic. Full article

The impact of freight on the transportation system is accentuated by the fact that trucks consume a greater roadway capacity than other vehicles and therefore cause more significant problems including traffic congestion, traffic delays, crashes, and pavement damage. Evaluating the actual repercussions of truck traffic becomes paramount in locales where roadway expansion is unfeasible. Trucks are vital to the economy, providing essential services to commerce and industry, and yet it is crucial that their operation does not contribute to the deterioration of infrastructural quality or compromise public safety. Currently, we lack methodologies in practice for the real-time management of traffic, specifically for truck routing, to minimize travel times and prevent delays due to non-recurrent congestion, such as traffic incidents. Accordingly, this study aimed to devise a truck routing strategy utilizing a traffic micro-simulation model (VISSIM) and to assess its effects on reducing travel delays. This involved the development of real-time truck re-routing simulation models that take into account non-recurrent congestion and the resulting travel delays and fuel consumption. The VISSIM model was applied to the I-75 corridor in Marion County, Florida, focusing on non-recurrent congestion effects on travel delays and fuel consumption. The initial findings suggest that the implementation of a dynamic truck re-routing system can significantly alleviate traffic congestion, resulting in a marked decrease in travel delays and fuel usage, demonstrating the potential for such strategies to enhance the overall efficiency of the transportation system. Full article

Aerosols influence Earth’s climate by interacting with radiation and clouds. Remote sensing techniques aim to enhance our understanding of aerosol forcing using ground-based and satellite retrievals. Despite technological advancements, challenges persist in reducing uncertainties in satellite remote sensing. Our study examines retrieval biases in MODIS sensors on Terra and Aqua satellites compared to AERONET ground-based measurements. We assess their performance and the correlation with the AERONET aerosol optical depth (AOD) using 14 years of data (2010–2023) from 29 AERONET stations across 10 Central–East European countries. The results indicate discrepancies between MODIS Terra and Aqua retrievals: Terra overestimates the AOD at 16 AERONET stations, while Aqua underestimates the AOD at 21 stations. The examination of temporal biases in the AOD using the calculated estimated error (ER) between AERONET and MODIS retrievals reveals a notable seasonality in coincident retrievals. Both sensors show higher positive AOD biases against AERONET in spring and summer compared to fall and winter, with few ER values for Aqua indicating poor agreement with AERONET. Seasonal variations in correlation strength were noted, with significant improvements from winter to summer (from R² of 0.58 in winter to R² of 0.76 in summer for MODIS Terra and from R² of 0.53 in winter to R² of 0.74 in summer for MODIS Aqua). Over the fourteen-year period, monthly mean aerosol AOD trends indicate a decrease of −0.00027 from AERONET retrievals and negative monthly mean trends of the AOD from collocated MODIS Terra and Aqua retrievals of −0.00023 and −0.00025, respectively. An aerosol classification analysis showed that mixed aerosols comprised over 30% of the total aerosol composition, while polluted aerosols accounted for more than 22%, and continental aerosols contributed between 22% and 24%. The remaining 20% consists of biomass-burning, dust, and marine aerosols. Based on the aerosol classification method, we computed the bias between the AERONET AE and MODIS AE, which showed higher AE values for AERONET retrievals for a mixture of aerosols and biomass burning, while for marine aerosols, the MODIS AE was larger and for dust the results were inconclusive. Full article

Due to the recurrent starting and stopping operations of automobiles during service, their engines’ hot ends are continually subjected to high-temperature cyclic oxidation. Therefore, it is crucial to develop ferritic stainless steels with better high-temperature oxidation resistance. This study focuses on improving the high-temperature cyclic oxidation performance of 18Cr-Mo (444-type) ferritic stainless steel by alloying with high-melting-point metal W and the rare earth element Ce. For this purpose, a high-temperature cyclic oxidation experiment was designed to simulate the actual service environment and investigate the high-temperature cyclic oxidation behavior and microstructure evolution of 444-type ferritic stainless steel alloyed with W and Ce. The oxide structure and composition formed during this process were analyzed and characterized using scanning electron microscopy/energy dispersive spectroscopy (SEM-EDS) and electron probe X-ray micro-analyzer (EPMA), in order to reveal the mechanism of action of W and Ce in the cyclic oxidation process. The results show that 18Cr-Mo ferritic stainless steel alloyed with W and Ce exhibits an excellent resistance to high-temperature cyclic oxidation. The element W can promote the precipitation of the Laves phase between the matrix and the oxide film, and the small-sized Laves phase can inhibit the interfacial diffusion of oxidation reaction elements and prevent the inward growth of the oxide film. The element Ce can refine oxide particles and reduce the thickness of the oxide film. CeO₂ particles within the oxide film can serve as nucleation sites for the formation of oxide particles from reactive elements, and they also contribute to pinning the oxide film, thereby enhancing its adhesion. Full article

The Net Primary Productivity (NPP) of the Tibetan Plateau (TP) has undergone significant changes since the 1980s. The investigation of the spatiotemporal changes of NPP and its driving factors is of significant importance. Here, we analyze the spatial and temporal trends of Net Primary Production (NPP) and the effects of meteorological factors on the NPP change on the Tibetan Plateau (TP) using version 5.0 of the Community Land Model. The results showed that the average NPP was 256 (g C·m²·yr⁻¹) over the past 40 years, with a continuously increasing trend of 2.38 (g C·m²·yr⁻¹). Precipitation was the main factor affecting NPP changes, temperature had no significant effect on NPP changes, while radiation showed a negative trend. Changes in precipitation, temperature and radiation account for approximately 91%, 5.3%, and 3.8% of NPP variation, respectively. Based on grass coverage, we categorized alpine grasslands into three types: high, medium, and low coverage. Our findings indicate the NPP change of the high-coverage grasslands was mainly affected by precipitation, and then the temperature and radiation. Comparatively, the precipitation change is the driving factor of the increased NPP of low-coverage grasslands, but the temperature increase is the negative factor. Our studies have implications for assessing and predicting vegetation responses to future climate change. Full article

The agricultural sector emphasizes sustainable development and energy efficiency, particularly in optimizing water pumping systems for irrigation. Brushless DC (BLDC) motors are the preferred prime mover over induction motors due to their high efficiency in such applications. This article details the rotor design and analysis of an energy-efficient BLDC motor with specifications of 1 hp, 3000 rpm, and 48 V, specifically tailored for a centrifugal monoset pump for irrigation. The focus lies in achieving optimal energy efficiency through grey wolf optimization (GWO) algorithm in the rotor design to determine optimal dimensions of the Neodymium Iron Boron (NdFeB) magnet as well as its grade. The finite element method analysis software, MagNet, is used to model and analyze the BLDC motor. The motor parameters, such as speed, torque, flux functions, temperature, and efficiency, are analyzed. For performance comparison, the same model with different magnet models is also analyzed. Validation via 3D finite element analysis highlights improvements in magnet flux linkage, stator tooth flux density, and rotor inertia with increased magnet thickness. Simulation results affirm the consistent performance of the designed BLDC motor, preferably when efficiency is increased. This efficiency and the constant speed lead to an improvement in the overall conversion efficiency of 7% within its operating range, affirming that the motor pump system is energy-efficient. Full article

A botnet is a network of compromised computer systems, or bots, remotely controlled by an attacker through bot controllers. This covert network poses a threat through large-scale cyber attacks, including phishing, distributed denial of service (DDoS), data theft, and server crashes. Botnets often camouflage their activity by utilizing common internet protocols, such as HTTP and IRC, making their detection challenging. This paper addresses this threat by proposing a method to identify botnets based on distinctive communication patterns between command and control servers and bots. Recognizable traits in botnet behavior, such as coordinated attacks, heartbeat signals, and periodic command distribution, are analyzed. Probabilistic models, specifically Hidden Markov Models (HMMs) and Profile Hidden Markov Models (PHMMs), are employed to learn and identify these activity patterns in network traffic data. This work utilizes publicly available datasets containing a combination of botnet, normal, and background traffic to train and test these models. The comparative analysis reveals that both HMMs and PHMMs are effective in detecting botnets, with PHMMs exhibiting superior accuracy in botnet detection compared to HMMs. Full article

Adiponectin is an important adipokine involved in glucose and lipid metabolism, but its secretion and potential role in regulating glucose utilization during ovarian development remains unclear. This study aims to investigate the mechanism and effects of follicle-stimulating hormones (FSHs) on adiponectin secretion and its following impact on glucose transport in the granulosa cells of rat ovaries. A range of experimental techniques were utilized to test our research, including immunoblotting, immunohistochemistry, immunofluorescence, ELISA, histological staining, real-time quantitative PCR, and transcriptome analysis. The immunohistochemistry results indicated that adiponectin was primarily located in the granulosa cells of rat ovaries. In primary granulosa cells cultured in vitro, both Western blot and immunofluorescence assays demonstrated that FSH significantly induced adiponectin secretion within 2 h of incubation, primarily via the PKA signaling pathway rather than the PI3K/AKT pathway. Concurrently, the addition of the AdipoR1/AdipoR2 dual agonist AdipoRon to the culture medium significantly stimulated the protein expression of GLUT1 in rat granulosa cells, resulting in enhanced glucose absorption. Consistent with these in vitro findings, rats injected with eCG (which shares structural and functional similarities with FSH) exhibited significantly increased adiponectin levels in both the ovaries and blood. Moreover, there was a notable elevation in mRNA and protein levels of AdipoRs and GLUTs following eCG administration. Transcriptomic analysis further revealed a positive correlation between the expression of the intraovarian adiponectin system and glucose transporter. The present study represents a novel investigation, demonstrating that FSH stimulates adiponectin secretion in ovarian granulosa cells through the PKA signaling pathway. This mechanism potentially influences glucose transport (GLUT1) and utilization within the ovaries. Full article